|
|
woodworking forums
Making a Campaign Table... - Woodwork Forums
Part One This is a somewhat duplicitous title as not only has my wife been campaigning to have this table made for some considerable time, but the subject of the post is a compact folding table of.
Part One This is a somewhat duplicitous title as not only has my wife been campaigning to have this table made for some considerable time, but the subject of the post is a compact folding table of.
First Pen - Woodworking Talk - Woodworkers Forum
I met a old Army guy (Joe) through the turning club in New Orleans that agreed to teach me what he knows about making pens, even though I am a Marine. Joe is big on Freedom Pens (Pens are made and.
I met a old Army guy (Joe) through the turning club in New Orleans that agreed to teach me what he knows about making pens, even though I am a Marine. Joe is big on Freedom Pens (Pens are made and.
Need advice on HSC major - Woodwork Forums
Good day I'm starting my HSC major woodworking project im planning to make a work bench,the timber im thinking of using- blue gum and Tasmanian oak. What are your recommendations? Can you.
Good day I'm starting my HSC major woodworking project im planning to make a work bench,the timber im thinking of using- blue gum and Tasmanian oak. What are your recommendations? Can you.
FS: Northfield woodworking machinery for sale, new & used ...
Northfield woodworking machinery for sale, new & used. Northfield 16" Jointer new, never used $11000 - 5 hp heavy-duty direct drive - 3600 rpm, 230v, 3-phase - straight knife, 4 knife cutterhead - 3-phase, fully wired with long rubber ...
Northfield woodworking machinery for sale, new & used. Northfield 16" Jointer new, never used $11000 - 5 hp heavy-duty direct drive - 3600 rpm, 230v, 3-phase - straight knife, 4 knife cutterhead - 3-phase, fully wired with long rubber ...
Adult apprenticeships? - Renovate Forums
Hello All, I've been slowly renovating our home over the last 3 months and have always had a keen interest in woodworking and building/construction. I'm looking to make a career change and get an.
Hello All, I've been slowly renovating our home over the last 3 months and have always had a keen interest in woodworking and building/construction. I'm looking to make a career change and get an.
My first table - Woodwork Forums
I had a few weeks off work and managed to knock up a little side table for my lounge room. The top is Western red cedar cut into 2 veneers book matched on a ply substrate with Tasmanian Oak frame,
I had a few weeks off work and managed to knock up a little side table for my lounge room. The top is Western red cedar cut into 2 veneers book matched on a ply substrate with Tasmanian Oak frame,
A new thread leader is just around the corner - North Carolina ...
Acceptable topics are birthdays, births, deaths, new job, woodworker featured in the local paper etc. Please do not use this forum for "off topic" discussions, and keep in mind that it should really be an announcement (where the only ...
Acceptable topics are birthdays, births, deaths, new job, woodworker featured in the local paper etc. Please do not use this forum for "off topic" discussions, and keep in mind that it should really be an announcement (where the only ...
Carving in copper - Router Forums
This is a discussion on Carving in copper within the Pyrography and Carving forums, part of the General Woodworking category; I read an article by Bob Smalser on making a brand from an old copper . ...
This is a discussion on Carving in copper within the Pyrography and Carving forums, part of the General Woodworking category; I read an article by Bob Smalser on making a brand from an old copper . ...
WIP - Kman's Traditional Work Bench - Woodwork Forums
Over two years ago I started planning and decided to build a more traditional work bench. I took lots of advice, read some texts and made some sketches... I even acquired some timbers for the purpose.
woodworking forums
Over two years ago I started planning and decided to build a more traditional work bench. I took lots of advice, read some texts and made some sketches... I even acquired some timbers for the purpose.
FOR SALE:VIC Swedish Paring Chisels - Woodwork Forums
G'day mates, I have for sale 3 Swedish paring chisels. Sizes are 3/8, 1/2 and 5/8 inch. The 3/8 wide is socket EA Berg, while the 1/2 and 5/8 chisels are Toledo. Asking for $25 each + postage. These.
G'day mates, I have for sale 3 Swedish paring chisels. Sizes are 3/8, 1/2 and 5/8 inch. The 3/8 wide is socket EA Berg, while the 1/2 and 5/8 chisels are Toledo. Asking for $25 each + postage. These.
woodworking forums
© 2005